Volume control on a per-note basis with MultiMics

[stefangant]

So I want to do a Drum Sampler, where there is a close and a room mic for each drum. I want to create an Interface with individual volume controls for close and room mics for each drum.
I thought of some solutions to achieve this, but none of them does exactly what I want to do (at least with my knowledge of HISE so far...):

1.) Message.setGain : with this command I cannot control both mics individually
2.) control the volume of every singe sample: also here, the MultiMics are merged into "one Sample" so I don't have individual control... plus I have a total of 1500 samples so I assume it won't be very efficient.
3.) Multichannel / MultiMic Routing: all of the drums have two Mic channels, "close" and "room". so I can route "close" to 1+2 and 3+4, but again, I cannot control the volume of the individual drums.

Is there a way to route certain samples to certain busses within one sampler? (e.g. samples with ID 0-9 are routed to 1+2, ID 10-19 to 3+4, ID 10-19 to 5+6 and so on...)

Another possible solution could be to use a separate Samplers inside HISE for each drum... BUT I have about 12 drums, so I would need 12 Sampler. That won't be very efficient either, or?

Has anybody a better solution for this? TIA!

[Lindon]

@stefangant said in Volume control on a per-note basis with MultiMics:

So I want to do a Drum Sampler, where there is a close and a room mic for each drum. I want to create an Interface with individual volume controls for close and room mics for each drum.
I thought of some solutions to achieve this, but none of them does exactly what I want to do (at least with my knowledge of HISE so far...):

1.) Message.setGain : with this command I cannot control both mics individually
2.) control the volume of every singe sample: also here, the MultiMics are merged into "one Sample" so I don't have individual control... plus I have a total of 1500 samples so I assume it won't be very efficient.
3.) Multichannel / MultiMic Routing: all of the drums have two Mic channels, "close" and "room". so I can route "close" to 1+2 and 3+4, but again, I cannot control the volume of the individual drums.

Is there a way to route certain samples to certain busses within one sampler? (e.g. samples with ID 0-9 are routed to 1+2, ID 10-19 to 3+4, ID 10-19 to 5+6 and so on...)

Another possible solution could be to use a separate Samplers inside HISE for each drum... BUT I have about 12 drums, so I would need 12 Sampler. That won't be very efficient either, or?

Has anybody a better solution for this? TIA!

well there are any number of solutions - but you are likely going to want to apply different effects to each drum, so at some point you are going to want different samplers for different drums - 12 samplers is not out of the question inefficient...

[d.healey]

@lindon What we really need is per group send FX

[Christoph Hart]

Another possible solution could be to use a separate Samplers inside HISE for each drum... BUT I have about 12 drums, so I would need 12 Sampler. That won't be very efficient either, or?

This is the best solution and if you decrease the voice count of each sampler, it will not be inefficient.

[Lindon]

@d-healey said in Volume control on a per-note basis with MultiMics:

@lindon What we really need is per group send FX

"group"? How dare you mention groups? You K**takt groupie...

[Dan Korneff]

@stefangant said in Volume control on a per-note basis with MultiMics:

I would need 12 Sampler

I have just over 30 samplers in one of my drum plugins. Works just fine here