Strange 'Jumping' using assigned knobs



  • Hi all,

    I've made an interface and have knobs assigned to parameters on different fx in HISE. Most all work fine, but I'm getting a very strange 'jumping' between values on 2 of them.

    The 2 knobs I'm trying to control are the 'Saturation' knob and 'PhaseFX' mix knob, which both should run as 'normalised percentages' I believe? Both are jumping very weirdly when turning up the values.

    Do I have a setting wrong somewhere? I'll add screen-shots of my settings below...

    Thanks in advance

    Screen Shot 2019-06-30 at 18.07.06.png

    Screen Shot 2019-06-30 at 18.03.37.png

    Screen Shot 2019-06-30 at 18.06.50.png

    Screen Shot 2019-06-30 at 18.02.56.png



  • Normalized percentage should have min 0 and max 1. If you add a knob and set its mode to normalized percentage you don't need to change anything else.

    HiseSnippet 882.3ocwV0riTaDDt6cmdIyBAEPnb1WPZQBhFS.BRbXmr+LnQjcwJyBhajd6tLSqoc2F61j0Dk2BtvC.2xCQdTfKbNuAIUa6Yr2jgM6bHj4zz0Oc8UU8UU6nLq.xysYDZ+iJSAB8RrIkF2zcmxUFx38HzKyNfm6frfZQ6TlxyyAIgRW+gdAz98HU+9is2gq4FAzJhPdpUIfePknbsRiF9HkVOhKgiTIcr9NCGKrlcsZaAhm0YCHobwL9KfC4dyViQnaruT4rYSbbGji1riUVNYp8mM01+TUt5XM3ODRlfWTsXxtSUZYz7bMmPn8hZy70qy7qwNPIUKj2VA9pJEAsdzsFPW6zPp2ofT3mBRirZo+B9Dvi1Ad8pg2UXSDYpTWqFO1tHarAaNwbrr2EV01Rn+NaWKZfw8MI7YvnL7vBG15dCFbyf6NXvMdPbgQ3TVSf0bn0AO1r0M17W1r+l+5lA+cUwwKUmOLYVsFxVpZemN6rbbKSQxwP1MCdEWW.KLDS+SWe237UeE0YcGCslwFk6woPy41NP3R5.jlxluWzfPzTWUm3xMchIZkDxHJ7Rt.6QF6wgjJv2vnG9gW+lsIOY7dbGe90f2HFkTHyo7ICcO3U37QcCtOaOHelylVYaRp03iO8R+qA8DBkQ+MLhk9+7N7O4tReIYiJCHIJoTCQ1bkuj2Nu89syKhiUm3qAWmDqzI4NLDiSvQNB8prmjCARHlWncA4yvgAsxLCjGYqlESrRzpulcnMKgqUuFjQPl.gr26z4kxwROGMZJGuqQOKDmnyvgYj.5UvvAqSv8A+CtNNwYkEZt6zig98MMJ7IRW9tmTavDrr69nUX1bvRmMWJy3bB2qvhTNwzki20VBdQNx+03sYS2Wx1ONFDtVv1iM5YelWqcg4r9JxAF950YsTktvYTF7xBvHJCaqWkCWH81sRe6vQ.HOFe3nQ1OEG+ws87rNSkz0Oq2QBWg2QnmS1vUaRr++ou+nsvoLu3.NNq62bbXQxD7AWAff0X.cteIxZ9Mf0mG3O6AzDvHqN7m3uFkg9yzFkgyU9YIFIbQl84h5cy9VwWTIAyaS0mKzG+tE7bvhkx9ZCtJT8bgvS3uEVcVtG2dk83aWYOtyJ6wcWYOt2J6w2sxdb+yvC+WM88ENaRMeGEDse0igT59FNxbqn9j+hFRPMI
    


  • @d-healey Thanks mate. That's fixed it. You saved the day, yet again!! Cheers ☺



  • @SteveRiggs you probably also want to be careful to make sure the middle position is set to something reasonable...


Log in to reply
 

17
Online

1.6k
Users

4.6k
Topics

42.7k
Posts