Collaborative project!

[lalalandsynth]

@ustk Quick question.
How best to keep pushing and pulling stuff when I have exported as vst and now have build folder in my project ?
Do I remove that , or is it removed when I pull or how does that work ?

[ustk]

@lalalandsynth I've just checked the Leslie phase, it's mono-compatible on my system...
Tested on monitors and headphones via a monitoring controller.

Their just a "normal" level change due to rotation, but it might be too obvious...

Also, there's a drop in level when the Leslie's ON, so this along with the level change might make a weird effect?

[ustk]

@lalalandsynth What I tend to do is to select everything I don't want to push in the changes list, and discard them...
We should use gitIgnore, but if you delete the folder (I do it quite often), they come back in the changes list. So discard is easier to me...

[lalalandsynth]

I see, so when I pull it just adds the changes , but not what I have changed .
As in it keep my build folder. Assume it does , want to be sure.

[lalalandsynth]

My mono compatibility test.
https://youtu.be/ywANVcYSndc

[ustk]

@lalalandsynth Ok I changed the Leslie low end to be 100% mono so we're sure...

[lalalandsynth]

@ustk ok, there would only be one mic on the low horn.
Working on Top main graphic and Product shots.
Will pull a bit later and test again.

[ustk]

@lalalandsynth Ok so it's cool
But strange, here it's less obvious, but I'm quite sure it's because of the drawbars patch I have...
Anyway, problem gone ;)

[ustk]

@lalalandsynth Is it I or the general level is low than yesterday?
The meter was almost hitting the 0dB at full level, now it's like /2

[lalalandsynth]

@ustk In pro model we can add another lower gui for ..

1.more tweakable reverb.
2.Saturation
3. Mic settings on Leslie.

:)

[lalalandsynth]

@ustk said in Collaborative project!:

@lalalandsynth Is it I or the general level is low than yesterday?
The meter was almost hitting the 0dB at full level, now it's like /2

Testing in Hise or DAW ?
Not sure , did not observe the levels .

[ustk]

@lalalandsynth said in Collaborative project!:

@ustk In pro model we can add another lower gui for ..

1.more tweakable reverb.
2.Saturation
3. Mic settings on Leslie.

:)

And even more ;)

Testing in Hise or DAW ?

In hise, I was used to see the meter going further.
Also at full level, I need to push my monitor controller a lot more, above the habitual comfortable level I use.
So I think adding the possibility of pushing the knob to +12dB might be a good solution

[lalalandsynth]

Ok, I am getting this weird thing when starting play.
In the video you can hear it easily when I stop and start play.
Almost hurts my ears .
https://youtu.be/R-g-OK--tiY

[d.healey]

You should add a got ignore file to avoid tracking the build folder.

[ustk]

@lalalandsynth Strange, will test that after lunch...

Ok so the last changes I've pushed are:

• Chorus ON/OFF inversion
• Leslie low end is 100% mono
• Level can go up to +12dB
• Preset panel has 2 columns instead of 3

[ustk]

@d-healey When I do that it never works if I delete the binary folder and build again...
I might doing something wrong...

[hisefilo]

Morning guys!!! 8AM here. reading :)

[lalalandsynth]

JAMMING !
https://youtu.be/kvsWPFntqSU

[ustk]

@lalalandsynth Youhou!!!!

[hisefilo]

@lalalandsynth Yeahhhhhhhh :)